Western Boise Appliance Repair
Western Boise Appliance Repair | 208-344-4893 we serve Meridian, Kuna, Eagle, and surrounding areas. We provide washer repair, dryer repair, refrigerator repair, dishwasher repair, and oven repairs.
Monday, April 12, 2021
dryer repair
A small component like this can be trouble when it goes bad. This bad door switch can and will stop your dryer from turning ON and drying your clothes. We carry these parts on our Boise service trucks so we can fix this dryer quickly.
Thursday, May 23, 2019
Slide-In Whirlpool Oven Repair
Our techs at Western Appliance Repair in Boise completed an
interesting service call today for a Whirlpool Oven.
These pictures show what disassembly is necessary to replace
a bad cooling fan motor in a slide-in oven.
The disassembly is quite severe to say the least. This is not a problem for us however. We can tackle a job like this one with ease.
When we arrived on site we ran a diagnostics program to
confirm the blower was indeed not working.
The blower was inoperable and when we actuated the control relays
remotely we received no response. This
suggests we may have a bad motor or, as we’ve seen in the past, a bad control
board. In some cases the blower motor
AND the main control board will need to be replaced due to compatibility
issues. In this particular case however,
the cooling fan was the only thing that was replaced.
After repair was completed and new fan installed, we ran a
diagnostic program to verify proper fan operation. Our nice customer informed is that the oven
has been working perfectly with no more error messages.
A job well done!
https://www.westernappliancerepairboise.com
Tuesday, April 2, 2019
Dryer Repair - Thermostat Operation
Hello, it’s Rich again from Western Appliance. We did six more repairs today. It seems that appliances never stop breaking.
In this picture we see two different components. One is a dryer high limit thermostat and the other is a thermal fuse. These important components regulate the dryer element’s heat – which is used for heating the interior of the drum when you dry clothes. They do not regulate the temperature inside the dryer drum however. I hope I did not confuse you. The only thing these components do is regulate the dryer element heat alone, that’s it. The dryer uses separate components which regulate the internal drying temperature. I’ll try to explain this a better way – if you wanted to start a campfire with a match you would want that match to burn at a sufficient temperature to light a fire. Once the fire is started then you can regulate the fire with the addition of wood or reducing the fires oxygen. Well, these thermostats regulate the “match”. The heat inside the dryer is controlled by a separate thermostat or temperature sensor.
They are mounted to the electric heating element housing and prevent overheating. It is very common to find these on most every dryer we encounter in Boise and Meridian.
Thursday, March 14, 2019
Too much dryer lint
Lint can be a real problem with dryers because it restricts the air flow inside the dryer drum during the drying cycle. Air flow in the drum during the drying cycle is very important because the moisture from the wet clothes needs to be flushed out. The air flow also needs to cool the heater element to prevent overheating and damage. The clothes will take longer to dry and also can cause damage to thermostats, heaters, and electronics.
This picture shows lint buildup around the heater element and the thermostats. This lint buildup suggests there may be a vent restriction. Air back-pressure causes this lint to flow inwards and into the interior of the dryer.
Dryer vents should be professionally cleaned at regular intervals to maintain proper dryer operation and to avoid costly repairs. Western Appliance can recommend a good company to have this service performed. For any questions feel free to call Rich at 208-344-4893 or visit our website at https://appliancerepairboise.com
Thank you
Rich
Tuesday, March 5, 2019
GE Dishwasher - Poor Washing
GE's latest dishwasher design is a very popular and dependable appliance. As with most appliances they can and will have minor and major functionality problems. In this case the dishwasher was not filling the tub with enough water to ensure proper functionality. Problems like this can be a great inconvenience to our Boise homeowners. When appliances break down, nobody is happy.
When I arrived I ran a diagnostic routine on the appliance and found that indeed, the tub was not filling completely with water - at least to it's specified level. It would fill with water for about 10 seconds, stop, then fill again for a couple more seconds. Then, instead of the hearing the wash motor turning on, I would hear a clicking sound - repeatedly. It appeared the sound was coming from under the toe-kick area of the appliance. This is where the main control board is located. Although a problem like this should be verified by doing voltage checks at the control board connector this "clicking" sound is a tell-tale sign of a possible malfunction with control board. A faulty control board was verified by looking at a "switching" voltage at the water control valve and an absence of a control voltage at the dishwasher wash motor.
Well, long story short, I arrived today, installed a brand new control board, and the now the dishwasher functions great! Boise Appliance Service 208-344-4893
When I arrived I ran a diagnostic routine on the appliance and found that indeed, the tub was not filling completely with water - at least to it's specified level. It would fill with water for about 10 seconds, stop, then fill again for a couple more seconds. Then, instead of the hearing the wash motor turning on, I would hear a clicking sound - repeatedly. It appeared the sound was coming from under the toe-kick area of the appliance. This is where the main control board is located. Although a problem like this should be verified by doing voltage checks at the control board connector this "clicking" sound is a tell-tale sign of a possible malfunction with control board. A faulty control board was verified by looking at a "switching" voltage at the water control valve and an absence of a control voltage at the dishwasher wash motor.
Well, long story short, I arrived today, installed a brand new control board, and the now the dishwasher functions great! Boise Appliance Service 208-344-4893
Wednesday, August 15, 2018
Proper Washer Loading
Many times while loading clothes into front-loading washing machines we
overlook some simple yet effective preventative actions that can prevent
a appliance repair visit.
I receive many repair calls from Boise homeowners who describe a rip or chunk that has been taken out of their washer door seal. Most times the rip is in the six o’clock position. Most never realize what causes this. I’ve heard things such as their little fluffy dog had bitten a piece out of it or their toddler bit a piece out of it. Ha Ha.
No, what actually causes this rip in the washer seal is improper loading of the clothes. When the clothes are not pushed to the back of the drum far enough before the door is closed it sets up the perfect conditions for seal to rip. If the clothing is hanging out just a small amount when the door is closed, it pinches the clothing between the seal and the inner door. When the drum goes into the spin mode, it will rip a chunk right out of the seal in the six o’clock position.
Unfortunately, this can happen after a new seal has been installed. I always warn my customers of this when I run into this type of repair.
Learn more appliance repair tips
I receive many repair calls from Boise homeowners who describe a rip or chunk that has been taken out of their washer door seal. Most times the rip is in the six o’clock position. Most never realize what causes this. I’ve heard things such as their little fluffy dog had bitten a piece out of it or their toddler bit a piece out of it. Ha Ha.
No, what actually causes this rip in the washer seal is improper loading of the clothes. When the clothes are not pushed to the back of the drum far enough before the door is closed it sets up the perfect conditions for seal to rip. If the clothing is hanging out just a small amount when the door is closed, it pinches the clothing between the seal and the inner door. When the drum goes into the spin mode, it will rip a chunk right out of the seal in the six o’clock position.
Unfortunately, this can happen after a new seal has been installed. I always warn my customers of this when I run into this type of repair.
Learn more appliance repair tips
Saturday, February 24, 2018
Just when I thought spring was around the corner winter rears it's semi-ugly head, well that is unless your s skier or just love snow. I'm right in the middle. I love the snow but hate the delays and the dangerous driving. I had 5 jobs I had to complete today. A washer, dryer, dishwasher, oven, and refrigerator repair. What an assortment in one day! Oh well, to start things off, it took me 1 hour to drive 6 miles on Victory Road in Meridian. The freeway was backed up and everyone was driving extremely slow. Most thought it was a good idea to take side streets. Well I guess everyone had that idea by the looks of it. Well, I guess we should count our blessings, this is a great place to live.
Rich
Western Boise Appliance Repair
208-344-4893
Rich
Western Boise Appliance Repair
208-344-4893
Subscribe to:
Posts (Atom)