Thursday, June 19, 2014

Washer enclosure removal

Some of my other posts did not show detail for the removal of washer clips.  Once these clips have been removed the washer enclosure can be pulled off.  Here is a pic that shows where to place the screwdriver in relation to clip.

Tuesday, June 10, 2014

Washer pump fix

Had a washer pump that would not pump out the water.  This was very unusual sor these maytag direct-drive washers.  In this instance the motor would spin. The impeller would spin, but no pump.  No clogs either.  Wierd appliance!  Oh we'll, we replaced it with a new one.

Tuesday, May 20, 2014

Bad Maytag washer pump bearing

This is a drain pump I pulled from a maytag washer.  You can see the metallic area that has been exposed around the bearing area.  The customer had been complaining about a screeching sound during the spin cycle.  These cannot be repaired and must be replaced.  

Friday, May 16, 2014

Boise zoo appliance repair

We repaired two dryers at the Boise zoo today.  Here is a pic of a robotic dinosaur in the pond.  The kids really got excited watching this thing roar.  That was fun.   Both of the dryers we fixed were frigidaire stack units so there was a lot of labor involved.  The personnel were very friendly and we got to see how the animals food was prepared.  Can you say crickets?  They had a lot of those for the lizards.

Monday, April 28, 2014

Washer Motor Coupler Replacement | Appliance Repair Boise



Motor Coupler – How to Install
 Motor Coupler for Direct Drive Appliance

When your motor coupler goes bad on your washing machine - Kenmore, Whirlpool, or Maytag washer - the inner tub will no longer spin and the agitator will not rotate. You will likely hear a loud grinding sound when the washer is in use.  A motor coupler replacement is a common repair.  At Western, we provide this Boise service at a very reasonable cost.

The motor coupler is a small rubber and plastic piece that couples torque from the motor, through the transmission, and into to the drive shaft of the appliance.  Because the washer’s motor coupler transmits all the motor torque, it makes sense that it will receive the most mechanical stress of the system.  This part may be prone to breakage after five or so years.  The following procedure will give you tips on the repair and replacement of washer’s motor coupler.  If you feel you cannot perform this task, call a professional appliance repair company in your area.

Caution:  Before any appliance repair is attempted, please disconnect electrical power to the unit.  Electricity will kill you if you are not careful.

Step number one is to remove the control panel so you can access the cabinet clamps.

Most direct-drive washers have two screws on the back of the control panel, one on each far end, pointing downwards. You will have to look closely to find them. A flashlight and Phillips-head screwdriver with an extension will help perform this easily.  Remove the two screws all the way without dropping them in the back of washer. Gently pull the front of the panel forward and rotate the front side of panel upwards. Rotate panel all the way backwards and lean it against the wall.

Step number two is to remove the appliances enclosure. Using a large flat-blade screwdriver, insert into slot and push the screwdriver handle away from you to release each clamp.

Remove the two clamps completely and set aside.  Disconnect the lid switch connector, which is located just under the control panel, which you just removed.  The connector will be very evident.  Slowly pull the top of the washing machine enclosure towards you so it pivots near your toes.  It is useful to put your toes against the outside of the enclosure to prevent it from moving.  Once pulled all the way towards you, release your toes and pull the enclosure off its base.  Set this aside.

Locate the washer drain pump. Direct Drive Pump for Washer 
 It is secured to the motor with two clamps.  Remove the hex screws securing the clamps and set aside.  Use a large flat-head screwdriver to pry away the clamps and removed the pump from the motor shaft.  You do not have to remove the water hoses.  Remove the motor clamps and remove the motor.  You will now see the motor coupler.  Washer Motor for Direct Drive Appliance

If the motor coupler is bad, you will see broken plastic pieces worn rubber.  If in doubt, replace it.

When installing a new coupler, I suggest you use one of the new couplers with the metal insert in the center.  These rarely go bad and are worth the extra few dollars. 

Tap the new coupler on to the motor and transmission shaft, line-up the teeth, and reinstall.  Note – if you need to tap on the motor coupler to secure a proper fit, be sure to tap the metal insert instead of the plastic – which is prone to breakage.

Tuesday, February 4, 2014

Garage Refrigerator Kit for Frigidaire Refrigerators


I get many garage refrigerator repair calls in the winter months when temperatures dip to 0 degrees and below.  Most cases involve lower-end Frigidaire or Whirlpool Top-Mount refrigerators, or in other words, refrigerators with the freezer mounted on the top.

In most cases, these refrigerators have the thermostat installed inside the refrigerators.  When the outside temperature gets too cold, the cold air permeates into the refrigerator and the thermostat will not turn on the compressor.  Now there is a fix for this.

Frigidaire has come out with a Frigidaire Refrigerator Garage Kit, which when properly installed, heats the thermostat to compensate for the cold air and prevents the freezer defrosting.  There is also a do-it-yourself Procedure for this if you follow the link in the YouTube description field.